@article { author = {zahiri, Javad and Jafari, Ahmad}, title = {Design and Construction of Electronic Irrigation Canal Gate}, journal = {Irrigation and Water Engineering}, volume = {13}, number = {1}, pages = {191-205}, year = {2022}, publisher = {انجمن علمی مهندسی آبیاری و آب ایران}, issn = {2251-7359}, eissn = {}, doi = {10.22125/iwe.2022.158524}, abstract = {Water level and flow control gates are the most important parts of any irrigation network. Most of the gates located in the irrigation networks face problems after the operation. While mechanizing gates for surface irrigation systems can greatly save water consumption and increase water efficiency. In this project, it was tried to design and construct a gate using modern technologies, which can be intelligently operated and able to pass the desired discharge. Bubble rubber was used to seal the gate and minimizing water loss. Electromotor, encoder, ultrasonic sensor, inverter, and PLC were used to mechanize the gate. An ultrasonic sensor was applied to read the water level. All the computations of the gate-opening rate are performed by the PLC and then the instructions are transmitted to the electromotor. The encoder is connected to the electromotor and, according to the computations, controls the number of motor revolutions for a given opening rate. The TIA Portal environment used to control the gate motion system. The program written in the TIA Portal environment includes all the settings related to the flow discharge, gate opening, sensitivity of the ultrasonic sensor, and gate-opening rate to provide the flexibility of the gate in real conditions. In order to calibrate the constructed sluice gate according to the obtained equation, several experiments were used and finally, the coefficient of 0.625 was obtained as a correction coefficient. The coefficient of determination and root mean square error for the calibrated equation were calculated to be 0.97 and 0.66, respectively. These results showed the suitable performance of the automatic gate based on a calibrated equation}, keywords = {Irrigation network,Water efficiency,PLC,TIA Portal environment}, title_fa = {طراحی و ساخت دریچه الکترونیکی کانال‌های آبیاری}, abstract_fa = {دریچه­های تنظیم سطح آب و کنترل دبی از مهمترین بخش­های هر شبکه آبیاری به حساب می­آیند که اغلب پس از بهره­برداری دچار مشکل شده و تنظیم دقیق میزان دبی عبوری از طریق این دریچه­ها تقریبا غیرممکن می­گردد. مکانیزه کردن دریچه­های سیستم­های آبیاری سطحی تا حد زیادی می­تواند باعث صرفه­جویی در میزان آب مصرفی و افزایش راندمان گردد. بر همین اساس در این طرح سعی گردید با استفاده از تکنولوژی­های نوین، دریچه­ای طراحی و ساخته شود که با توجه به میزان دبی تعریف شده و سطح آب بالادست بتواند به صورت هوشمند عمل کرده و دبی مورد نظر را از خود عبور دهد. برای آب­بندی دریچه از لاستیک­های آب­بند حبابی شکل استفاده گردید تا میزان هدررفت آب به کمترین مقدار خود برسد. قطعات مورد استفاده جهت مکانیزه کردن دریچه شامل: موتور، انکودر، سنسور التراسونیک، اینورتر و PLC می­باشند. تمامی محاسبات مربوط به میزان بازشدگی دریچه توسط PLC انجام می­گیرد و پس از آن دستورات لازم به الکتروموتور منتقل می­شود. انکودر به موتور متصل بوده و با توجه به محاسبات صورت گرفته تعداد دورهای موتور را برای میزان بازشدگی مشخص کنترل می­کند. جهت کنترل سیستم حرکتی دریچه از محیط TIA Portal استفاده گردید. برنامه نوشته شده در محیط TIA Portal کلیه تنظیمات مربوط به میزان  دبی عبوری، میزان بازشدگی دریچه و حساسیت سنسور التراسونیک و دریچه را شامل می­شود. برنامه به­گونه­ای نوشته شده است که بتواند انعطفاف­پذیری دریچه در شرایط واقعی را تامین نماید. جهت بررسی میزان دقت دریچه، از مدل آزمایشگاهی استفاده گردید. با توجه به آزمایشات صورت گرفته، رابطه به­دست آمده جهت میزان بازشدگی دریچه کالیبره گردید. ضریب تعیین و ریشه میانگین مربعات خطا برای معادله اصلاح شده به ترتیب برابر با 97/0 و 66/0 محاسبه گردید که نشان­دهنده عملکرد مناسب دریچه خودکار ساخته شده بر اساس رابطه اصلاح شده می­باشد.}, keywords_fa = {شبکه آبیاری,راندمان,PLC,محیط TIA Portal}, url = {https://www.waterjournal.ir/article_158524.html}, eprint = {https://www.waterjournal.ir/article_158524_ab57ca6364e9ce02fcf5cf9becef26c0.pdf} }