@article { author = {Rostamabadi, Massumeh and Salehi Neyshaboury, Ali akbar}, title = {Effect of Changing parameters of intake and main channel on the distance of dividing stream line from outer wall of bend}, journal = {Irrigation and Water Engineering}, volume = {9}, number = {1}, pages = {32-45}, year = {2018}, publisher = {انجمن علمی مهندسی آبیاری و آب ایران}, issn = {2251-7359}, eissn = {}, doi = {}, abstract = {Direct dewatering of the river is used for irrigation and water supply and etc. Dewatering without diversion dam leads to a sediment settlement at the downstream of intake in the main river. The distance of dividing stream line from the outer bank of the bend influences the amount of sediment entering the intake. Anything that reduces the distance of dividing stream line from the outer wall of the bend at the bottom of the main channel, will reduces sediment entering the intake. The geometric and hydraulic parameters of intake and main channel affect the distance of dividing stream line from the outer bank. In this study the effect of parameters such as width and position of the intake, diversion angle and height of the sill (Each one changes in four levels) on the distance of dividing stream line from the outer wall using the SSIIM numerical model is investigated. Also three angles (50, 110 and 170 degrees) and three different Froude numbers (0.288, 0.305 and 0.322) for bend and three discharges ratio (10, 18 and 25 percent) for lateral intake are considered. Taguchi method is used in the design of studies. The results show that changing in width and position of the intake, diversion angle and height of the sill have less influence on the distance of dividing stream line from the outer wall of the bend, but the variations of dividing stream line from the outer wall of the ben relative to the discharge ratio almost ascending and linear. Also, in a fixed-angle bend, changing the Froude number has a very small effect on the distance of dividing stream line. The Surface flow duct width is 0.9 to 1.25 times the width of the duct in the bed}, keywords = {Intake,Dividing stream-line,Bend of river,SSIIM2}, title_fa = {تغییرات فاصله خط تقسیم جریان از دیواره خارجی قوس با تغییر پارامترهای آبگیر و آبراهه اصلی}, abstract_fa = {آبگیری از رودخانه به منظور کشاورزی، آبرسانی و ... به کار می­رود. آبگیری بدون بند انحرافی منجر به نشست رسوبات در پایین دست آبگیر در رودخانه اصلی می­شود. فاصله خط تقسیم جریان انحرافی از دیواره آبگیر بر مقدار رسوب ورودی به آن تأثیرگذار است. هر عاملی که منجر به کاهش فاصله خط تقسیم جریان ورودی به آبگیر در کف آبراهه اصلی شود، باعث کاهش رسوب وارد شده به آبگیر خواهد شد. پارامترهای هندسی و هیدرولیکی آبگیر و آبراهه اصلی بر فاصله خط تقسیم جریان در آبگیری از قوس مؤثرند. در پژوهش حاضر تأثیر پارامترهای عرض و موقعیت آبگیر، زاویه آبگیری و ارتفاع آستانه (هر یک در چهار سطح تغییر) بر فاصله خط تقسیم جریان از دیواره خارجی آبراهه قوسی، با استفاده از مدل عددی SSIIM بررسی شده است. برای قوس سه زاویه مرکزی 50، 110 و 170 درجه و سه عدد فرود 288/0، 305/0 و 322/0 و برای آبگیر جانبی سه دبی آبگیری نسبی 10، 18 و 25 درصد درنظر گرفته شده است. روش تاگوچی در طراحی مطالعات به­کار رفته است. نتایج نشان داد تغییر عرض و موقعیت آبگیر، زاویه آبگیری و ارتفاع آستانه تأثیر بسیار کمی بر تغییرات فاصله خط تقسیم جریان از دیواره خارجی دارد، اما تغییرات فاصله خط تقسیم جریان نسبت به دبی نسبی آبگیری صعودی و تقریباً خطی است. همچنین در قوس با زاویه مرکزی ثابت، تغییر عدد فرود تأثیر بسیار کمی بر نسبت فاصله خط تقسیم جریان دارد. همچنین عرض مجرای جریان در سطح 9/0 تا 25/1 برابر عرض مجرای جریان در کف تعیین شد.}, keywords_fa = {آبگیر,خط تقسیم,قوس رودخانه,SSIIM2}, url = {https://www.waterjournal.ir/article_81828.html}, eprint = {https://www.waterjournal.ir/article_81828_5eab213a44d313cb4bb316a1f408d12e.pdf} }